ELMconfig USB device 500kbit/s ELM327 compatible interface with MS-CAN switch for Forscan FoCCCus OBD2 diagnostics …

Product Information

Do not change any options with RCM airbag module unless you know what you are doing""¦. Lets not switch any airbags off eh? Turn on the car ignition but don’t start the engine! At this point, you can launch the ELM327 software. It will automatically detect the OBD2 reader and the vehicle ECU. Don’t get me wrong about Torque Lite. The free version of Torque is good enough for basic applications but it had trouble reading the trouble codes on some Nissan and Subaru vehicles. After you’ve paired the app with your scan tool, you can begin car diagnostics! image courtesy of Chris Running the Car Diagnostics with the ELM327 software If you want to configure modules,many of the BT units will fail and refuse without OBD2 adapter to progarm them.

You can save the Changed AS-BUILT information if you like and also save the connection log file if you like. After the MK3.5 was introduced the FoCCCus software turned out to be not fully functional on the MK3.5. This is because of the different hardware and software version numbers of the MK3.5. At that time the original developer of the program did not plan to modify the program to work with the MK3.5. ELMConfig can't open a connection to the adapter at all, no matter which mode or laptop I try (Yes, FORScan is closed when I try to use ELMConfig). In all cases, it pops up an error saying "Correct response from adapter timed." Usually, the request and response are both empty, as in this screenshot I took:

Note: when connecting if FORScan says “No ELM Found”, flip the toggle switch to the other position and restart the connection process.If the OHP ELMconfig USB device connects, this is the HS-CAN position.Mark the adapter accordingly. I've explicitly set the adapter to use 500,000bps in ELMConfig, and it confirms that setting in the window titlebar. Do read these forums and guides first for any problems, particularly in setting up the program and modifying the interface. I will try to help with questions for Kuga people here on this forum but I am no expert. I have used this program on my Kuga and it worked for me and I simply wish to share my experience with you folks. Ensure there is NO yellow exlamation marks (that looks like this ) next to devices such as: USB-Serial CH340 | FT232R USB UART Prolific | USB-to-Serial | USB Serial Port | USB2.0-Serial | Silicon Labs CP210x USB to UART Bridge What i saw was >K followed by what i typed each time , i had to over write the commands each time twice before i got each one to OK or >K

I worked on a lot of cars, and I really mean a LOT! I started tinkering with cars in high school. My experience allowed me to test drive and diagnosis a multitude of makes and models, including prestigious German cars. FORScan Lite for Android - attention: some functions are missing in FORScan Lite. Please see comparison of applications OK failed at the finalhurdle, after reading firmwear from PCM took 80 minutes then loaded firmware from phf/hex/bin fileGot the long list above after the car decided to not talk to the PATS module I think and immobilized. Reset fault codes and it seemed happy then I then selected the Configuration & Programming menu from the vertical set of icons on the left of the Forscan window (the chip icon below the spanner icon) EDIT* NOTE PuTTy is not needed for ELMconfig Program , once Elm327 is connected then select configure from the menu on startup of ELMconfig , this will send all commands to re-configure your ELM327. The Elm interface, unmodified, can access modules within the car that uses the high speed CAN-BUS (HS-CAN) but can be rewired to access modules using the medium speed CAN-BUS (MS-CAN). The modification using a switch enables you to access both systems easily. In Elmconfig, each module is listed under each bus speed as required.

It is advisable that no other USB devices are connected to your computer. Select the correct COM port where the vLinker FS is connected. If there are multiple usb devices connected to your pc, you will need to determine which one is correct from the Device Manager. This update will enable a system which tries to detect a deflating tyre. This system does not use sensors in the wheel, instead it uses the ABS wheel speed sensors to detect when a wheel is rotating at a different speed to the others when it shouldn’t be. A deflating wheel will have a smaller circumference, so will rotate faster than the other wheels. This may not work on all cars. This resulted in a list of options including, in my case, puddle lights and retractable rear view mirrors. (Just about every factory option seems to be listed including Cruise control, Global Open/Close, City Stop, Auto headlights,… I haven’t tried editing any of these though) C) the tool has been through umpteen revisons and some don't allow you to complete these steps with one version of the tool

Best ELM327 Software for Windows Smartphones

at this point Forscan showed a scrolling list of the modules it had found (after prompting me to toggle the toggle switch between MS & HS positions to complete the listing) Having connected the ELM327 module to the PC USB port and car OBD port and launched Forscan, I switched the ignition on when prompted – on my keyless start model this meant pressing the power button without pressing the clutch